Menú

Mostrar Mensajes

Esta sección te permite ver todos los mensajes escritos por este usuario. Ten en cuenta que sólo puedes ver los mensajes escritos en zonas a las que tienes acceso en este momento.

Mostrar Mensajes Menú

Temas - damian_cap28

#1
hola a todos tengo una placa de red wifi awus036h, utilizo el backtrack 5, 2.6.32-21-generic, y despues de googlear hasta el cansancio di con una posible solucion, para mi problema de que no me la reconocia.
Desde terminal seguimos los siguientes pasos.
1. sudo rmmod r8187 rtl8187 mac80211 cfg80211
2. sudo mkdir /usr/src/drivers
3. cd /usr/src/drivers
4. sudo wget http://dl.aircrack-ng.org/drivers/rtl8187_linux_26.1010.zip
5. sudo unzip rtl8187_linux_26.1010.zip
6. cd rtl8187_linux_26.1010.0622.2006/
7. sudo wget http://patches.aircrack-ng.org/rtl8187_2.6.27.patch
8. sudo wget http://patches.aircrack-ng.org/rtl8187_2.6.32.patch
9. sudo tar xzf drv.tar.gz
10. sudo tar xzf stack.tar.gz
11. sudo patch -Np1 -i rtl8187_2.6.27.patch
12. sudo patch -Np1 -i rtl8187_2.6.32.patch
13. sudo make
14. sudo make install
15. sudo modprobe r8187

extracto del siguiente link: http://www.ubuntizandoelplaneta.com/2010/05/solucion-problemas-con-alfa-awus036h-en.html

Ahora me la reconoce la placa:

root@bt:~# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:off/any 
          Mode:Managed  Frequency:2.462 GHz  Access Point: Not-Associated   
          Bit Rate:54 Mb/s   Tx-Power:32 dBm   
          RTS thr:2347 B   Fragment thr:2346 B   
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

wlan1     802.11b/g  Mode:Managed  Access Point: Not-Associated   
          Bit Rate:11 Mb/s   Tx-Power=5 dBm   
          Retry:on   Fragment thr:off
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

root@bt:~# airmon-ng


Interface   Chipset      Driver

wlan0      Unknown      ndiswrapper
wlan1      RTL8187      r8187

tengo dos preguntas nuevas ahora por que cuando uso el wicd network la señal de todas las redes me da  -1 y la segunda pregunta es como cargo la configuracion para que sea cargada en el inicio del sistema.

Gracias a todos y espero una pronta respuesta. saludos a toda la comunidad.

 
#2
Hola a todos, buenas tardes. Tengo una Compaq presario v3918 LA, con el disco particionado en dos partes. En una corre win 7 y en la otra bt 5 R1, la pregunta es como hago ahora para poner en modo minitor mi placa Alfa AWUS036H rtl8187?? por que con todo lo googleado no puedo puedo conseguir. Gracias... :D


root@bt:~# lsb_release -a
No LSB modules are available.
Distributor ID:   Ubuntu
Description:   Ubuntu 10.04.3 LTS
Release:   10.04
Codename:   lucid

root@bt:~# uname -r
2.6.32-21-generic




root@bt:~# lspci
00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.3 Co-processor: nVidia Corporation MCP67 Co-processor (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2)
00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2)
00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:12.0 VGA compatible controller: nVidia Corporation C67 [GeForce 7150M / nForce 630M] (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
01:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
01:09.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 12)
01:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
01:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff)
08:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)

root@bt:~# lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 007: ID 1c4f:0003 SiGma Micro
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Bus 001 Device 003: ID 04f2:b016 Chicony Electronics Co., Ltd VGA 30fps UVC Webcam
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

root@bt:~# dmesg | tail -20
[   57.461976] [TTM] Zone highmem: Available graphics memory: 998164 kiB.
[   57.461990] [drm] nouveau 0000:00:12.0: 64 MiB VRAM
[   57.462815] [drm] nouveau 0000:00:12.0: 64 MiB GART (aperture)
[   57.463120] [drm] nouveau 0000:00:12.0: Allocating FIFO number 0
[   57.463401] [drm] nouveau 0000:00:12.0: nouveau_channel_alloc: initialised FIFO 0
[   57.463537] [drm] nouveau 0000:00:12.0: nouveau_channel_free: freeing fifo 0
[   57.464568] [TTM] Zone  kernel: Used memory at exit: 0 kiB.
[   57.464574] [TTM] Zone highmem: Used memory at exit: 0 kiB.
[   57.776059] usb 3-2: new low speed USB device using ohci_hcd and address 6
[   57.989892] usb 3-2: configuration #1 chosen from 1 choice
[   58.000092] input: SIGMACHIP Usb Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input14
[   58.000220] generic-usb 0003:1C4F:0003.0005: input,hidraw0: USB HID v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-0000:00:02.0-2/input0
[   93.004039] Clocksource tsc unstable (delta = -301060337 ns)
[ 3604.055162] usb 3-2: USB disconnect, address 6
[ 4893.564062] usb 3-2: new low speed USB device using ohci_hcd and address 7
[ 4893.777351] usb 3-2: configuration #1 chosen from 1 choice
[ 4893.787899] input: SIGMACHIP Usb Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input15
[ 4893.788276] generic-usb 0003:1C4F:0003.0006: input,hidraw0: USB HID v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-0000:00:02.0-2/input0
[ 7800.832521] eth0: link down.
[ 8022.719144] eth0: link up.

root@bt:~# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:off/any 
          Mode:Managed  Frequency:2.462 GHz  Access Point: Not-Associated   
          Bit Rate:54 Mb/s   Tx-Power:32 dBm   
          RTS thr:2347 B   Fragment thr:2346 B   
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

PD: si se requieren algun otro dato solo pidanlo y grax a todos.