Señal Power On en fuentes de alimentación ATX, modificación [duda]

[von Newman]

Saludos, pues estaba leyendo un poco sobre precisamente las fuentes de alimentación  y mencionaban las señales Power On en fuentes ATX:

Power On es una señal de las placas madres que se utiliza para apagar el sistema mediante software. Esto permitirá también el uso opcional del teclado para encender de nuevo el sistema.

Curso de Armado y Reparacion de PC

Y me surgió la duda de lo último, por lo que estuve buscando un poco más de cómo modificarlo para usar el teclado para encender de nuevo el sistema, si es que con eso se refiera a que no es necesario usar el botón de encendido.

¿Alguien puede indicarme cómo es que se modifica para encenderla de esta forma?
En dado caso de que descompusiera el botón de encendido de mi máquina, ¿cómo puedo hacer para encenderla con el teclado? o ¿hay alguna otra manera, a parte de comprar y repara esa parte?

Gracias, espero prontas respuestas!

[Aprendiz-Oscuro]

Buenas.

Mira si tienes en BIOS alguna opcion--> "Power On By PS2 Keyboard" <Enable> En un ordenador que tengo aqui al lado tiene dicha opción xD.

Igual tienes que cambiar algun jumper también... Mirate el manual de tu placa base, ahí te deberia venir explicandote las distintas secciones y opciones de BIOS de todas formas.





Saludos!!

[von Newman]

Cierto! Tiene que ser de la BIOS, en el Manejo de opciones de encendido, ahora probaré si existe esta función para windows 7, por cierto dejo esta info que encontré gracias a Aprendiz-Oscuro.

ACPI Suspend to RAM : ACPI stands for Advanced Configuration and Power Interface - not to be confused with APIC or IPCA, which some people may find as options in their BIOS setup programs. The Suspend to RAM feature, sometimes referred to as S3/STR, lets the PC save more power when in Standby mode, but all devices within or attached to the computer must be ACPI-compliant. Some BIOS's offer an S1/POS option for this scenario. If you enable this feature and experience problems with the standby mode, simply go back into the BIOS and disable it.

Video Off Method : The DPMS (Display Power Management System) option allows the BIOS to control the video display card if it supports the DPMS feature. The Blank Screen option simply blanks the screen - use this for monitors without either power-management or "green" features. The V/H SYNC Blank option blanks the screen and turns off vertical and horizontal scanning. If your computer and monitor were built within the last four years, I recommend setting this to DPMS.

HDD Down In Suspend : This feature determines whether the hard-disk drive is automatically shut down when the computer enters Suspend mode. While most power settings of this type are controlled within Windows, if you find the hard drive is not powering down when the computer enters Suspend mode - assuming your computer even allows Suspend and Hibernate modes - then enable this option. Otherwise, the recommended setting is Disabled.

PWR Button < 4 Secs : By default, all ATX computers will power off after the power button is held for more than four seconds. This setting tells the computer what to do if the power button is held down for less than four seconds. The options are to power off the system or enter Suspend mode. This setting is up to you.

Power Up On PCI Device : If you use Wake-On-LAN - typically employed in large office environments to turn on computers for remote administration - you will want this setting Enabled. Otherwise, I recommend you set it to Disabled.

Wake/Power Up on Ext. Modem : This setting tells the computer to turn itself on when a phone line plugged into its modem rings. Once again, this is used for remote administration. For other environments - in other words, most users - I recommend you set this to Disabled.

Automatic Power Up : This feature, if enabled, lets you designate a specific time each day when the PC will turn itself on. If that's useful to you, set it to Enabled. Otherwise, I recommend Disabled.

Time (hh:mm:ss) of Alarm : This field sets the time for automatic power-up, based on a military/24-hour clock. The Automatic Power Up field must be enabled to use this feature.

AC Power Loss Restart : This option lets you tell the PC what to do when power is restored after an unexpected loss of power. Disabled leaves the system off, while Enabled reboots the system. Previous State sets the system back to the state it was in before the power interruption. I recommend you set this to Disabled.

Power On By PS/2 Mouse : When enabled, this feature allows the use of a PS/2 (not USB) mouse to turn on the system. Disabled is recommended, so you don't accidentally keep turning on your computer.

Power On By PS/2 Keyboard : When enabled, this feature lets specific keys on a PS/2 keyboard be used to turn on the system. Disabled is recommended, as most people find this of an annoyance when they accidentally press the wrong key.

http://www.tomshardware.com/reviews/bios-beginners,1126-8.html

supongo que de ahí tomaste la imagen
saludos!